2. C C Product. Submersible pump for pumping clean water, surface water and waste water containing solids or long-fibred material. Denomination. Dataplate. rpm. Max 40°C. YSER/Y//V. 26/51A. kWhp. Date: Flygt CS MT. Use our handy online form to submit details on your existing Flygt pump to get a Flygt C Submersible Pumps Range Flygt C LT Submersible.
|Published (Last):||8 November 2015|
|PDF File Size:||16.49 Mb|
|ePub File Size:||17.70 Mb|
|Price:||Free* [*Free Regsitration Required]|
Flygt Series / C Submersible Pumps
Take all necessary measures to avoid over-pressurization. This includes any modification to the equipment or use of parts not provided by Xylem. If there is a question regarding the intended use of the equipment, please contact an Xylem representative before proceeding. For information about how to transport and store the pump, see Transportation and Storage in the Installation, Operation and Maintenance manual.
A hazardous situation which, if not avoided, could result in minor or moderate injury Electrical Hazard: Observe these rules when working with the product: Safety equipment Use safety equipment according to the company regulations. Use this safety equipment within the work area: The noise level of the product is lower than 70 dB. However, the noise level of 70 dB may be exceeded in some installations and at certain operating points on the performance curve.
Make sure that you understand the noise level requirements in the environment where the pump is installed. Failure to do so may result in hearing loss or violation of local laws. The work area Observe these regulations and warnings in the work area: Pay attention to the risks of electric shock or arc flash hazards.
Flygt 3000 Series / C Submersible Pumps
Product and product positioning requirements Observe these requirements for the product and the product positioning: Electrical connections regulations Electrical connections must fljgt made by certified electricians in compliance with all international, national, state, and local regulations.
Observe these guidelines and warnings for electrical connections: This guideline also applies to the control circuit. The screened cable is necessary to fulfill European CE requirements.
Contact your Xylem representative and ask your VFD supplier for electrical limitations. See also VFD recommendation in article no. Earthing grounding Observe the following regulations for earthing grounding connections. Earthing grounding regulation Comment Flyygt electric equipment must be earthed grounded. This rule applies to pumps and mixers as well as monitoring equipment. The earthing grounding conductors must be correctly connected.
Failure to follow this rule could result in a fatal accident. If the motor cable is disconnected by mistake, flygtt earthing grounding conductor needs to be disconnected last from its terminal. This rule applies to both ends of the cable.
Risk of electrical shock or burn.
You must connect an additional earth- ground- fault protection device to the earthed grounded connectors if persons are likely to come into physical contact with the pump or pumped liquids. Precautions during work Observe these safety precautions when you work with the product or are in connection with the product: Make sure that the pump is isolated from the system and that pressure is relieved before you disassemble the pump, remove plugs, or disconnect piping. Clean chemicals from the eyes 1.
Hold your eyelids apart forcibly with your fingers. Rinse the eyes for at least 15 minutes.
Product specifications | Flygt 3152 – Alaska Pump and Supply
Use an eyewash or running water. Clean chemicals from the body 1. Wash the skin with soap and water for at least one minute.
Seek medical attention, if required. Safety regulations for Ex-approved products in potentially explosive atmospheres Guidelines for compliance Compliance is only fulfilled when the pump is operated within its intended use, for example within its intended hydraulic range. The conditions of the service must not be changed without approval of an authorized Xylem representative. When installing or maintaining explosion-proof pumps, follow these guidelines: This manual clearly identify accepted methods for disassembling units.
These methods must be adhered to. Trapped liquid can rapidly expand and result in a violent explosion and injury. Never apply heat to impellers, propellers, or their retaining devices to aid in their removal.
If there are any questions regarding these requirements, the intended use, or if the equipment requires modification, contact an Xylem representative before you proceed. Personnel requirements Xylem disclaims all responsibility for work done by untrained and unauthorized personnel. These are the personnel requirements for Ex-approved products in potentially explosive atmospheres: Special rules apply to installations in explosive atmospheres.
Product and product handling requirements These are the product and product handling requirements for Ex-approved products in potentially explosive atmospheres: Dry running during service and inspection is only permitted outside the classified area.
Level-sensing equipment must be installed if the product can be operated at less than the minimum submersion depth. Equipment for monitoring For additional safety, use condition-monitoring devices. Condition-monitoring devices include but are not limited to these devices: Recycling guidelines Always recycle according to these guidelines: If the unit or parts are accepted by an authorized recycling company, then follow local recycling laws and regulations.
If the unit or parts are not accepted by an authorized recycling company, then return them to the nearest Xylem representative. Waste and emissions regulations Observe these safety regulations regarding waste and emissions: Reference for electrical installation For electrical installation requirements, consult your local electric utility.
Product warranty Coverage Xylem undertakes to remedy faults in products from Xylem under these conditions: Limitations The warranty does not cover faults caused by these situations: However, should the need arise for a warranty claim, then contact your Xylem representative. Spare parts Xylem guarantees that spare parts will be available for 15 years after the manufacture of this product has been discontinued. Inspect the package for damaged or missing items upon delivery.
Note any damaged or missing items on the receipt and freight bill. File a claim with the shipping company if anything is out of order. Unpack the unit 1. Remove packing materials from the unit. Dispose of all packing materials in accordance with local regulations.
Inspect the unit to determine if any parts have been damaged or are missing. Contact your Xylem representative if anything is out of order. Lifting guidelines General The following are general guidelines for lifting the unit: Make sure the unit hangs straight up and down from the lifting hook.
The unit and the components can be heavy. Use proper lifting methods and wear steel-toed shoes at all times. Never lift the unit by the motor cable or by the hose. Flygt Installation, Operation, and Maintenance Manual 9 Transportation and Storage Lifting equipment The lifting equipment must fulfill the following requirements: Contact Xylem for information.
Flygt – Alaska Pump and Supply |
Oversized lifting equipment could cause damage if the unit should stick when being lifted. Store the unit 1. After raising the unit, allow it to run for a short time to discharge all remaining pumped media liquid. Flygr unit is frost-proof while operating or immersed in liquid, but the impeller and the shaft seal may freeze if the unit is raised in a temperature below freezing. Store the unit in a covered and dry location free from heat, dirt, and vibrations.
If the unit is stored more than 6 months, rotate the shaft every other month to prevent the seals from sticking together. Before operating the unit after storage: Condition Action The unit has been stored more than 6 months Inspect the unit with special attention to the seals and the cable entry. The impeller is frozen Thaw the impeller by immersing the unit in liquid. Never use a naked flame to thaw the unit. Intended use The product is intended for moving waste water, sludge, raw and fkygt water.
Always follow the limits given in Application limits page Do NOT use the pump in highly corrosive liquids.
The use of other parts can invalidate any claims for warranty or compensation. For more information contact your Xylem representative. Flygt Installation, Operation, and Maintenance Manual 11 Product Description Parts 7 6 4 3 2 5 1 12 Positio Part n Description 1 Impeller A wide range of impellers are available for different applications and capacities.
Flygt Installation, Operation, and Maintenance Manual Product Description Monitoring equipment The following applies to the monitoring equipment of the pump: Optional sensors Thermistor Thermistors are optional sensors for measuring the temperature. They are connected in series in the flggt and activate the alarm at overtemperature. The sensors are only optional for standard pumps.