2002 CAMRY OWNERS MANUAL PDF

Buy Toyota Camry Owners Manual: Interior Accessories – ✓ FREE DELIVERY possible on eligible purchases. Toyota Camry – Owner’s Manual ( pages). Posted on 5 Feb, by Monstercheeto. Model: Toyota Camry. File size: MB. Other Toyota Camry Manuals: Toyota Camry – Owner’s Manual · Toyota Camry – Seats, Seat Belts, Steering Wheel And Mirrors.

Author: Faeran Zulkigor
Country: Suriname
Language: English (Spanish)
Genre: Life
Published (Last): 15 July 2006
Pages: 217
PDF File Size: 4.50 Mb
ePub File Size: 8.70 Mb
ISBN: 611-6-42523-325-2
Downloads: 54977
Price: Free* [*Free Regsitration Required]
Uploader: Tagor

Indicate the possibility of injury to you or other people. HINT Provide additional information to help you to perform the repair efficiently. The engine serial number is stamped on the cylinder block of the engine, and the transaxle serial number is stamped on the housing, as shown in the illustration. Engine Serial Number B: Be sure to lift and support the vehicle at the proper locations See page 01— Manuwl NOT exceed the rating, or use one with a lower rating.

If the clip is damaged during the operation, always replace it with a new clip.

When using a vacuum gauge, never force the hose camyr a connector that is too large. Use a step—down adapter for adjustment. Once the hose has been stretched, it may leak air. Even in case of a minor collision where the SRS does not deploy, the horn button assembly, instrument panel passenger airbag assembly, front seat canry assembly, curtain shield airbag assembly and seat belt pretensioner should be inspected See pages 60—17, 60—34, 60—44, 60—50 and 61—9.

When using electric welding, first disconnect the airbag connector 2 yellow pins under the steer- ing column near the combination switch connector before starting work. When disposing of a vehicle or the airbag assembly alone, the airbag should be deployed using an SST before disposal See page 60— Perform the operation in a safe place away from electrical noise. Oners disposing of a vehicle or the side airbag assembly alone, the airbag should be deployed using an SST before disposal See page 60— When disposing of a vehicle or the curtain shield airbag assembly alone, the manusl should be deployed using an SST before disposal See page 60— If the SRS wire harness becomes discon- nected or the connector becomes broken due to an accident, etc.

Never work cajry a place such as a pit or nearby a pit, as there is a possibility that vaporized fuel is filled in those places. Check that the antenna and feeder are correctly adjusted.

2002 Toyota Camry – Owner’s Manual (290 pages)

Do not install any powerful mobile communication sys- tem. Engine compression maunal must be performed as rapidly as possible. Do not run the engine when the fuel tank is nearly empty. This may cause the engine to famry and create an extra load on the converter. Attachment mm 3. Confirm the circuit for the system or the part which should be checked using the problem symptoms table or the results obtained in step 4. Repair Repair the affected system or part in accordance with the instructions in step 6.

  MAKESHIFT ARSENAL LOWRY PDF

After completing repairs, confirm that the problem has been solved. If the problem dose not reoccur, perform a confirmation test under the kwners conditions and in the same environment as when it occurred for the first time.

DTC troubleshooting or to the troubleshoot- ing of problem symptoms table. Troubleshooting of each problem symptom The problem is still occurring in a place other than the diagnostic circuit The DTC displayed first is either for a past problem or it is a secondary problem. Do not apply heat directly to the parts in the ECU. When the malfunction seems to occur when electrical load is excessive.

Turn on all the electrical loads including the heater blower, headlights, rear window defogger, etc. DTC is not displayed. Tc terminal circuit 05— procedure. Connection of the connector with a lock should be securely done until it makes a click sound.

WRONG In case of checking the connector with a Toyota electrical tester, perform it at the back side harness side of the connector using a mini test lead.

Minimum Motor Generator No. Inboard joint grease — g 6. Drain and refill 3. Airbag disposal Tire with disc wheel Width: Airbag disposal Inner diam.: To avoid surface damage.

Use the nut with the same number of the nut strength classification or the greater than the bolt strength clas- sification number when camfy parts with a bolt and nut. Fuel tank protector lower center x Fuel tank 48 in. Chain sub—assy Elongation Maximum Crank pin diameter Crankshaft bearing cap set bolt Diameter Standard 7.

Toyota Camry – Owner’s Manual – PDF ( Pages)

Valve spring deviation Maximum 2. Valve spring installed tension at Crankshaft bearing cap set bolt diameter Standard 7. Minimum opening pressure 69 kPa 0. Front wheel Water caamry x Cylinder block 71 in. Ignition coil x Cylinder head cover 80 in.

2000 Toyota Camry – Owner’s Manual (269 pages)

Brush exposed length Standard 1. Brush holder x Rectifire end frame 39 in. Ground clearance of front wheel center: Ground clearance of lower suspension arm No. Ground clearance of strut rod set bolt center: Stabilizer bar manhal Stabilizer bar x Stabilizer bar link Strut manuql x Body 1, Strut rod x Rear axle carrier 1, Parking brake cable x Body 48 in. Front axle hub bearing Deviation Maximum: Rear axle hub bearing Backlash Maximum: Rear axle hub bearing Deviation Maximum: Shock absorber x Rear axle carrier 2, Rear axle hub set bolt Rear axle carrier x Brake caliper Rear disc brake Rear drum brake shoe lining thickness Standard thickness: Front speed sensor wire harness clamp x shock absorber Bolt A: Parking brake shoe lining thickness Standard thickness: Parking brake shoe clearance between rear shoe and lever Less than 0.

  DATA SHEET OF 74LS373 PDF

Differential oil seal drive in depth LH side 0 ” xamry. A bolt 58 in. Transmission hub sleeve No.

Front differential pinion shaft No. Front differential side gear backlash Standard backlash 0. Shift lever slotted pin clearance to the shift lever inner assy —0. Shift lever slotted pin clearance to the shift lever inner No. Selecting bell crank assy x Transmission case Selecting bellcrank support x Selecting bellcrank No.

Flywheel runout Maximum 0. Diaphragm spring finger wear Maximum depth 0. Clutch 2002 point from pedal full stroke end position 25 mm 0. Clutch release cylinder assy x Transaxle housing Steering column assembly set bolt and nut Manuwl clutch clearance 1MZ—FE 0. Magnetic clutch clearance 2AZ—FE 0. Cooler condenser assy x Body 85 in. Wind shield wiper motor assy Wiper link assy 48 in. Check the engine speed when the OCV is operated by the hand—held tester.

Confirm the valve does not adhere. Bad returning of the valve by entrance of foreign objects causes subtle pressure leak to the advanced direction. Then, DTC can A be detected. Between terminal ownsrs and 5 No continuity E Using an ohmmeter, check that continuity exists be- tween terminals 3 and 5 when the battery voltage is applied across terminals 1 and 2.

Connect 2 water by—pass hoses to the throttle body assy. Connect the throttle body assy connector. Connect the vacuum hose to the throttle body assy.

Using an ohmmeter, check that no continuity exists between the terminal and body. Between terminal 3and 5 No continuity Using an ohmmeter, check that continuity exists be- tween terminals 3 and 5 when the battery voltage is applied across terminals 1 and 2. Body Gasket 2014 in. Remove the 2 set screws and throttle position sensor. Disconnect the throttle position sensor connector. See page 11—15 Drain the fuel remained inside the fuel pump tube.

Prevent the disconnected fuel pump tube from damaging and mixing foreign objects by covering them with a vinyl bag.